欢迎光临 济南鑫浩焊接技术有限公司官方网站!

关于我们|网站地图|加入收藏

全国热线: 134-5513-5688
0531-88635477
当前位置:主页 > 资讯中心 > 行业新闻 >

正确保养快速卡盘的方法

文章出处:济南鑫浩焊接技术有限公司关键词:变位机人气: 发表时间:2016-10-20 12:14 字体大小:【

  快速卡盘是机床等设备的的重要部件,平常要多注意保养和维护, 尤其是使用环境特殊或者包装特殊产品时更要增加保养的频率。下面小编带您详细介绍一下如何来正确保养快速卡盘,以便可以增长设备的使用寿命,提高工作生产效率。

  Quick chuck is an important part of machine tools and other equipment, usually have to pay more attention to the maintenance and maintenance, especially to increase the maintenance of special environment of special products or packaging frequency. The following Xiaobian take you to explain in detail how to properly maintain the rapid growth of chuck, to the service life of equipment, improve production efficiency.

  1、使用工作完成后必须使用风枪等工具对快速卡盘本体以及滑道表面进行清洁,这样可以保证车床快速卡盘长时间使用之后仍具有有良好精度,所以对快速卡盘的定期润滑工作很重要。

  1, after the completion of the work must use air gun and other tools for fast and clean the surface of the chuck body slide, which can guarantee the long time after using the fast lathe chuck has good precision, so regular lubrication is important for quick chuck.

  2、每天至少打一次二硫化钼油脂(颜色为黑色),将油脂打入快速卡盘油嘴内直到油脂溢出夹爪面或快速卡盘内孔处(内孔保护套与连结螺帽处)。

  2, every day at least once MoS2 grease (black), the oil into the oil nozzle until the oil overflow quick chuck jaw face or quick chuck hole (hole protective sleeve connected with the screw cap).

  3、为防止快速卡盘内部生锈,加持力降低,无法夹紧工件, 因此最好使用具有防锈效果的切削油,使用切削油可以预防快速卡盘内部生锈。

  3, in order to prevent the rapid internal chuck rust, the blessing is reduced, unable to clamp the workpiece, so it is best to use cutting oil with anti rust effect, the use of cutting oil can prevent internal rust fast chuck.

  4、作业完成时必须以风枪或类似工具来清洁快速卡盘本体及滑道面。

  The air gun or similar tool to clean and fast chuck body slide surface must be 4, when work is complete.

  5、快速卡盘至少每过6个月拆下清洗,保持夹爪滑动面干净并给予润滑,使快速卡盘寿命增长。

  5, quick chuck at least every 6 months to remove the cleaning, keep clean and give the jaw sliding surface lubrication, the rapid growth of chuck life.

  6、检查各部零件有无破裂及磨损之情形,削铸铁至少每2个月一次来彻底清洁,如遇严重有损零件应立刻更换新品。

  6, check the parts with no breakdown and wear of the situation, cutting cast iron at least once every 2 months to completely clean, such as the case of serious damage to the parts should be replaced immediately.

  7、针对不同工件必须使用不同夹持方式,若是使用它去夹不规则工件会造成快速卡盘损坏。

  7, according to different workpiece clamping methods must be different, if you use it to clamp the irregular workpiece will cause rapid damage to chuck.

  我们已做好准备,以全新的姿态迎接新老客户,欢迎您来电咨询,洽谈,我们将继续为您把好关,服好务。

  We are ready to meet new and old customers, welcome you to inquire, negotiate, we will continue to be good for you, good service.

下一篇:三维滑块的特点 上一篇:没有了

同类文章排行

最新资讯文章