欢迎光临 济南鑫浩焊接技术有限公司官方网站!

关于我们|网站地图|加入收藏

全国热线: 134-5513-5688
0531-88635477
当前位置:主页 > 资讯中心 > 行业新闻 >

正确保养卡盘的方法知识

文章出处:济南鑫浩焊接技术有限公司关键词:变位机人气: 发表时间:2016-10-20 11:32 字体大小:【

  卡盘是机床等设备的的重要部件,平常要多注意保养和维护, 尤其是使用环境特殊或者包装特殊产品时更要增加保养的频率。下面小编带您详细介绍一下如何来正确保养卡盘,以便可以增长设备的使用寿命,提高工作生产效率。

  Chuck is an important part of machine tools and other equipment, usually have to pay more attention to the maintenance and maintenance, especially to increase the maintenance of special environment of special products or packaging frequency. The following Xiaobian take you to explain in detail how to properly maintain the chuck, so as to increase the service life of equipment, improve production efficiency.

  1、使用工作完成后必须使用风枪等工具对卡盘本体以及滑道表面进行清洁,这样可以保证车床卡盘长时间使用之后仍具有有良好精度,所以对卡盘的定期润滑工作很重要。

  1, after the completion of the work must use air gun and other tools on the chuck body and slide surface cleaning, it can guarantee the lathe chuck is used for a long time still has good precision, so regular lubrication of the chuck is very important.

  2、每天至少打一次二硫化钼油脂(颜色为黑色),将油脂打入卡盘油嘴内直到油脂溢出夹爪面或卡盘内孔处(内孔保护套与连结螺帽处)。

  2, every day at least once MoS2 grease (black), the grease into the nozzle until the oil overflow chuck jaw face or chuck hole (hole protective sleeve connected with the screw cap).

  3、为防止卡盘内部生锈,加持力降低,无法夹紧工件, 因此最好使用具有防锈效果的切削油,使用切削油可以预防卡盘内部生锈。

  3, to prevent the chuck body rust, the blessing is reduced, unable to clamp the workpiece, so it is best to use cutting oil with anti rust effect, the use of cutting oil can prevent internal rust chuck.

  4、作业完成时必须以风枪或类似工具来清洁卡盘本体及滑道面。

  The air gun or similar tool to clean the chuck body and slide surface must be 4, when work is complete.

  5、卡盘至少每过6个月拆下清洗,保持夹爪滑动面干净并给予润滑,使卡盘寿命增长。

  5, chuck at least every 6 months to remove the cleaning, keep clean and give the jaw sliding surface lubrication, the chuck life growth.

  6、检查各部零件有无破裂及磨损之情形,削铸铁至少每2个月一次来彻底清洁,如遇严重有损零件应立刻更换新品。

  6, check the parts with no breakdown and wear of the situation, cutting cast iron at least once every 2 months to completely clean, such as the case of serious damage to the parts should be replaced immediately.

  7、针对不同工件必须使用不同夹持方式,若是使用它去夹不规则工件会造成卡盘损坏。

  7, according to different workpiece clamping methods must be different, if you use it to clamp the irregular workpiece chuck will cause damage.

  8、当卡盘压力不正常时使卡盘处于高压力下将工件夹住,这将会降低卡盘使用寿命。

  8, when the pressure is not normal to chuck chuck in high pressure workpiece clamped, which will reduce the service life of chuck.

  我们的反应釜质量好,价格实惠,服务周到 ,在业内一直深受新老客户的好评与青睐,而且我们坚信在以后的经营中我们本着诚信第一的原则会越做越好!

  The reactor the quality of our good, affordable, and thoughtful service, in the industry has been highly praised and favored by the old and new customers, and we believe that in the future business in our first principle of good faith will be better!

同类文章排行

最新资讯文章